CHALLENGER

CHAMPION BUS INC. Pdf Download PDF Report

Normal

Champion Bus Inc. submitted a model Challenger, diesel-powered 19 seat (including the driver) 25-foot bus, for a 7 yr/200,000 mile STURAA test.  The odometer reading at the time of delivery was 496 miles.  Testing started on December 6, 2006 and was completed on March 16, 2007.  The Check-In section of the report provides a description of the bus and specifies its major components. 

The primary part of the test program is the Structural Durability Test, which also provides the information for the Maintainability and Reliability results.  The Structural Durability Test was started on December 11, 2006 and was completed on March 12, 2007.

The interior of the bus is configured with seating for 19 passengers including the driver. Free floor space will accommodate 11 standing passengers resulting in a potential load of 30 persons. At 150 lbs per person, this load results in a measured gross vehicle weight of 15,030 lbs.  In order to avoid exceeding the GAWR (4,600 lbs) of the front axle and (9,880 lbs) of the rear axle, ballast for 6 standing passengers was eliminated. This reduction from full capacity resulted in an adjusted measured vehicle weight of 14,070 lbs and was used for all dynamic testing.  The first segment of the Structural Durability Test was performed with the bus loaded to a GVW of 14,070 lbs. The middle segment was performed at a seated load weight of 13,390 lbs and the final segment was performed at a curb weight of 10,410 lbs.  Durability driving resulted in unscheduled maintenance and failures that involved a variety of subsystems.  A description of failures and a complete and detailed listing of scheduled and unscheduled maintenance are provided in the Maintainability section of this report.

Accessibility, in general, was adequate. The alternator is located down low between the engine, wheel well and cowling.  The lower of the two A/C compressors is also difficult to access.  The remaining components covered in Section 1.3 (repair and/or replacement of selected subsystems), along with all other components encountered during testing, were found to be readily accessible and no restrictions were noted.

The Reliability section compiles failures that occurred during Structural Durability Testing. Breakdowns are classified according to subsystems.  The data in this section are arranged so that those subsystems with more frequent problems are apparent.  The problems are also listed by class as defined in Section 2.  The test bus encountered no Class 1 failures. The one Class 2 failure was the result of a failed factory recalled exhaust pressure sensor. The two remaining failures were both Class 4.

The Safety Test, (a double-lane change, obstacle avoidance test) was safely performed in both right-hand and left-hand directions up to a maximum test speed of 45 mph. The performance of the bus is illustrated by a speed vs. time plot.  Acceleration and gradeability test data are provided in Section 4, Performance.  The average time to obtain 50 mph was 17.00 seconds.

The Shakedown Test produced a maximum final loaded deflection of 0.229 inches with a permanent set ranging between -0.002 to 0.006 inches under a distributed static load of 11,100 lbs. The Distortion Test was completed with all subsystems, doors and escape mechanisms operating properly except the outer barrier of the handicap device did not deploy in a number of positions. No water leakage was observed throughout the test. All other subsystems operated properly. The test bus submitted for testing was not equipped with any type of tow eyes or tow hooks, therefore, the Static Towing Test was not performed.  The Dynamic Towing Test was performed by means of a front-lift tow.  The towing interface was accomplished using a hydraulic under-lift wrecker.  The bus was towed without incident and no damage resulted from the test. The manufacturer does not recommend towing the bus from the rear; therefore, a rear test was not performed.  The Jacking and Hoisting Tests were also performed without incident. The bus was found to be stable on the jack stands, and the minimum jacking clearance observed with a tire deflated was 8.8 inches. A Fuel Economy Test was run on simulated central business district, arterial, and commuter courses. The results were 6.75 mpg, 7.37 mpg, and 11.71 mpg respectively; with an overall average of 7.89 mpg. A series of Interior and Exterior Noise Tests was performed. These data are listed in Section 7.1 and 7.2 respectively.


 

Number: 0617
Model: CHALLENGER
Manufacturer: CHAMPION BUS INC.
Vin Number: 1FDXE45P15HA09646